Trade supplier of HVAC zoning, controls and air distribution components across Australia
AUSTRA SUPPLY
4-zone modulating controller, front panel with 25, 50, 75 and 100% settings for each zone
4-zone modulating controller, front panel with 25, 50, 75 and 100% settings for each zone4-zone modulating controller, front and back

Zoning and controls · Zone controllers

4-zone modulating controller

Part number: AS-ZC-4M

A wall controller for four zones. Each zone can be set to 25, 50, 75 or 100% open, not just on or off, with four LEDs showing the position. Any zone can be set as the spill zone.

Zones4
Positions25, 50, 75, 100% or closed
Supply24 VAC ±10%, 50 Hz
Zone output200 mA per channel
Modulating zonesMore than basic open/close.
Remembers settingsPositions kept after a power cut.

Overview

Most zone controllers only open or close a zone. This controller sets each zone to 25, 50, 75 or 100% open. Press OPEN once for fully open, and press again to step through the settings. Four LEDs on each zone show where the damper sits.

Any one zone can be set as the spill zone. When every other zone is closed, the spill zone opens on its own to relieve duct pressure. This protects the fan and stops the ducts from over-pressurising. Choose a duct near a return air grille, a corridor or a plant room, not a bedroom or office.

Damper positions and the spill setting are kept if the power goes out. The controller runs on 24 VAC from our 240 V to 24 V transformer and drives one F03 actuator per zone.

Typical applications

  • Homes and apartments
  • Small offices and shops
  • Upgrading an open/close system
  • Jobs where zones need part-open settings

Part numbers

Choose a quantity and add each part to your quote list. Prices are sent by written quote.

Part numberDescriptionSize (mm)MaterialUnitQuote
AS-ZC-4M4-zone modulating controller4 zonesEach

Specifications

Control

Zones4, each controlled on its own
Positions per zone25%, 50%, 75% and 100% open, or closed
Position displayFour LEDs per zone
Spill zoneAny one zone, set at the controller
Power lossPositions and spill setting kept after power returns
Zone labelsPre-printed and blank labels included

Electrical

Supply24 VAC ±10%, 50 Hz
Built-in fuse2.0 A resettable
Zone output24 VAC, 200 mA per channel
Cable to actuator20 m maximum

Environment

Operating temperature−10 °C to +60 °C
Operating humidity10 to 80% RH, non-condensing
Altitude0 to 2000 m

Specifications may change without notice. Contact us to confirm details for your project.

Wiring

Connect the transformer to 240 VAC mains (licensed electrician) and its 24 VAC output to the controller. Connect each F03 actuator to a channel, CH1 to CH4.

PowerTransformer240 VAC in, 24 VAC out
Control4-zone modulating controllerCH1 to CH4, 200 mA each
CableSix-core motor cable20 m maximum per run
ActuatorF03 actuatorOne per zone

Compatible products

Products that are often specified with the 4-zone modulating controller.

  • F03 motor kit

    Everything needed to motorise a zone, in one part number.

    AS-MK-F03
  • F03 damper actuator, angled view
    F03 damper actuator

    24 VAC damper actuator that holds any position. 3.9 N·m running torque, 1 RPM.

    AS-ACT-F03-24
  • 240 VAC 24 VAC
    240 V to 24 V transformer

    Steps 240 VAC mains down to 24 VAC for the controller and actuators.

    AS-TRF-24
  • Six-core motor cable, 15 m coil
    Six-core motor cable, 15 m

    One 15 m plug-in lead carries power and signal from controller to actuator.

    AS-CBL-6C-15M

Frequently asked questions

How do I set the spill zone?

Press and hold the OPEN button of the zone for more than 5 seconds. All four LEDs on that zone flash to confirm. To cancel, hold the CLOSE button of the spill zone for more than 5 seconds.

Which zone should be the spill zone?

Use a duct near a return air grille, a corridor or a plant room. Do not use a bedroom or office, because the spill zone will open on its own and affect comfort in that room.

What happens after a power cut?

Damper positions and the spill setting are kept. The zones return to where they were once power comes back.

Need pricing for a project?

Not sure which part you need? Send us the job or your schedule. We will work out the parts list and quote every line.